TOPIC 2.8 · STUDY
Spring Forces
Hooke's law treats spring force as restoring and proportional to displacement from the relaxed length. Equilibrium stretch follows from force balance for hanging loads, elevators, and frictionless inclines. Parallel and series combinations set an effective spring constant, and a spring between accelerating blocks carries the force needed by the trailing mass.
2.8.A
Spring forces
An ideal spring obeys Hooke's law: $F_s=-kx$. Here $x$ is the displacement of the free end from the spring's relaxed length, not the total length of the spring. Stretch ($x>0$ if you choose that way) and compression both count through $|x|$. The minus sign means the force points back toward the relaxed position: pull the end outward and the spring pulls inward; push it inward and the spring pushes outward. This course uses $g=10\,\mathrm{m/s^2}$ near Earth.
The constant $k$ is the slope of a force-versus-stretch graph: $k=\Delta F/\Delta x$, not the coordinates of a single plotted point. A line through the origin with rise $45\,\mathrm{N}$ over run $0.15\,\mathrm{m}$ has $k=300\,\mathrm{N/m}$. A real spring follows that straight line only up to a limit; beyond the elastic range the force is no longer proportional to stretch, so a single $k$ no longer describes the spring.
The slope of this $F$ versus $x$ line is the spring constant $k$. The quantity $x$ is measured from the relaxed length, not from zero coil length or from the ceiling attachment.
When a mass $m$ hangs at rest from a vertical spring, the upward spring force balances the weight: $kx=mg$, so the equilibrium stretch is $x=mg/k$. Example: $m=1.5\,\mathrm{kg}$ on a spring with $k=250\,\mathrm{N/m}$ gives $x=15/250=0.060\,\mathrm{m}$. Always subtract the relaxed length from the stretched length before dividing; using the full hanging length as $x$ is a common error.
In an elevator the same balance uses the apparent weight. Accelerating upward at magnitude $a$, the stretch satisfies $kx=m(g+a)$, so $x=m(g+a)/k$. Accelerating downward with $a<g$, the stretch is $x=m(g-a)/k$. With the $1.5\,\mathrm{kg}$ and $250\,\mathrm{N/m}$ spring, upward $a=3.0\,\mathrm{m/s^2}$ gives $x=1.5(13)/250=0.078\,\mathrm{m}$; downward $a=4.0\,\mathrm{m/s^2}$ gives $x=1.5(6.0)/250=0.036\,\mathrm{m}$.
On a frictionless incline of angle $\theta$, a spring parallel to the surface holds a block at rest when the spring force balances only the downhill component of weight: $kx=mg\sin\theta$, so $x=mg\sin\theta/k$. The normal force balances $mg\cos\theta$ and does not stretch the spring. Example: $m=4.0\,\mathrm{kg}$, $\sin\theta=0.60$, and $k=120\,\mathrm{N/m}$ give $x=24/120=0.20\,\mathrm{m}$.
| Situation | Force the spring balances | Equilibrium $|x|$ |
|---|---|---|
| Hang at rest | $mg$ | $mg/k$ |
| Elevator upward $a$ | $m(g+a)$ | $m(g+a)/k$ |
| Elevator downward $a<g$ | $m(g-a)$ | $m(g-a)/k$ |
| Frictionless incline | $mg\sin\theta$ | $mg\sin\theta/k$ |
Parallel springs sit side by side and share the same stretch $x$. Their forces add, so $k_{\mathrm{eff}}=k_1+k_2$. The stiffer spring carries more of the load: $F_i=k_ix$. Example: $k_1=80\,\mathrm{N/m}$ and $k_2=120\,\mathrm{N/m}$ give $k_{\mathrm{eff}}=200\,\mathrm{N/m}$. Under a $40\,\mathrm{N}$ load the common stretch is $0.20\,\mathrm{m}$, with $16\,\mathrm{N}$ on the softer spring and $24\,\mathrm{N}$ on the stiffer one.
Series springs are joined end to end. Each carries the full load $F$, the stretches add, and $1/k_{\mathrm{eff}}=1/k_1+1/k_2$. The softer spring stretches more. Example: $k_1=150\,\mathrm{N/m}$ and $k_2=300\,\mathrm{N/m}$ under $F=30\,\mathrm{N}$ stretch by $0.20\,\mathrm{m}$ and $0.10\,\mathrm{m}$, totaling $0.30\,\mathrm{m}$, which matches $k_{\mathrm{eff}}=100\,\mathrm{N/m}$. Cutting a uniform spring in half doubles $k$ for each half: fewer coils share the same force, so each half stretches half as much under that force.
A stiffer spring exerts a larger force only when the stretches are equal (the parallel case). In series the forces are equal and the softer spring takes most of the extension. Do not add the $k$ values for an end-to-end pair, and do not take the series reciprocal rule for a side-by-side pair.
If two blocks of masses $m$ and $M$ on a frictionless surface are joined by a spring and an external force $F$ pulls one of them so that both accelerate together, the common acceleration is $a=F/(m+M)$. Isolating the trailing block, the only horizontal force on it is the spring force, so that force equals the trailing mass times $a$. Example: $m=2.0\,\mathrm{kg}$ pulled by $F=16\,\mathrm{N}$ with trailing $M=6.0\,\mathrm{kg}$ and $k=160\,\mathrm{N/m}$ gives $a=2.0\,\mathrm{m/s^2}$, spring force $12\,\mathrm{N}$, and stretch $x=12/160=0.075\,\mathrm{m}$.
Key points
- Hooke's law is $F_s=-kx$ with $x$ measured from the relaxed length; stretch and compression both use $|x|$.
- $k$ is the slope of a force-versus-stretch graph ($F/x$), not a single point's coordinates; real springs leave the straight line past an elastic limit.
- Hanging at rest: $x=mg/k$. Elevator up: $x=m(g+a)/k$. Elevator down with $a<g$: $x=m(g-a)/k$.
- Frictionless incline: $x=mg\sin\theta/k$; the normal force balances $mg\cos\theta$.
- Parallel: $k_{\mathrm{eff}}=k_1+k_2$ and equal stretch; the stiffer spring carries more load.
- Series: $1/k_{\mathrm{eff}}=1/k_1+1/k_2$, equal force, stretches add; cutting a spring in half doubles each half's $k$.
- Equal stretch: stiffer means larger force. Equal force (series): softer means larger stretch.
- Two blocks accelerating together under $F$: $a=F/(m+M)$ and the spring force equals the trailing mass times $a$.
The minus sign in $F_s=-kx$ means the force is restoring (opposite the displacement from the relaxed position), not that the spring constant $k$ itself is negative.