TOPIC 2.9 · STUDY

Circular Motion

Uniform circular motion needs a net force toward the center equal to mass times speed squared over radius. Loops, hills, flat curves, banked turns, and conical pendulums all reduce to that radial requirement. Use g = 10 m/s^2.

2.9.A

Circular Motion

An object that moves in a circle of radius $r$ at speed $v$ has centripetal acceleration $a_c=v^2/r$ directed toward the center. That acceleration changes the direction of the velocity, not its magnitude, when the speed is constant. The period $T$ is the time for one full lap, so $v=2\pi r/T$ and therefore $a_c=4\pi^2 r/T^2$. Doubling the speed at fixed $r$ multiplies $a_c$ by four.

Newton's second law in the radial direction says the net force toward the center equals $m v^2/r$. Real forces such as tension, gravity, the normal force, and friction can contribute to that net inward push. There is no separate outward force on the free-body diagram; any "centrifugal" feeling is a frame effect, not an extra contact force.

A circle with an arrow from a point on the rim toward the center, labeled a.

The net force points toward the center.

Example: a puck on a string sweeps a horizontal circle of radius $2.5\,\mathrm{m}$ once every $1.0\,\mathrm{s}$. Then $v=2\pi(2.5)/1.0=5\pi\,\mathrm{m/s}\approx16\,\mathrm{m/s}$ and $a_c=4\pi^2(2.5)/(1.0)^2=10\pi^2\,\mathrm{m/s^2}\approx99\,\mathrm{m/s^2}$. If the same puck later runs at $8.0\,\mathrm{m/s}$ on a $2.0\,\mathrm{m}$ radius, $a_c=(8.0)^2/2.0=32\,\mathrm{m/s^2}$. Raise the speed to $16\,\mathrm{m/s}$ on that same circle and $a_c$ becomes $128\,\mathrm{m/s^2}$, four times as large.

If the object also speeds up or slows down, there is a tangential acceleration $a_t$ parallel (or antiparallel) to the velocity. The total acceleration is the vector sum of the inward centripetal part and the tangential part: $a=\sqrt{a_c^2+a_t^2}$. Just after an object starts from rest around a circle, $v$ is still near zero, so $a_c=v^2/r$ is tiny and the tangential part dominates.

A bead on a circular wire of radius $0.50\,\mathrm{m}$ starts from rest with tangential acceleration $2.0\,\mathrm{m/s^2}$. Immediately after release, $a_c\approx0$ and the total acceleration is essentially $2.0\,\mathrm{m/s^2}$ along the wire. Later, when $v=3.0\,\mathrm{m/s}$ and $a_t$ is still $2.0\,\mathrm{m/s^2}$, $a_c=(3.0)^2/0.50=18\,\mathrm{m/s^2}$ and the magnitude of the total acceleration is $\sqrt{18^2+2.0^2}\approx18\,\mathrm{m/s^2}$.

Location Radial equation (inward positive) Special speed
Top of vertical loop (inside track) $N+mg=mv^2/R$ Minimum contact: $v=\sqrt{gR}$ when $N=0$
Bottom of vertical loop $N-mg=mv^2/R$ $N$ exceeds the weight
Crest of a hill (center below) $mg-N=mv^2/r$ Leave road: $v=\sqrt{gr}$ when $N=0$

Inside a vertical loop of radius $R$, both the normal force and the weight point toward the center at the top, so $N+mg=mv^2/R$. The slowest speed that keeps the rider in contact is when $N=0$: $v=\sqrt{gR}$. With $g=10\,\mathrm{m/s^2}$ and $R=1.6\,\mathrm{m}$, that minimum is $\sqrt{16}=4.0\,\mathrm{m/s}$. At the bottom the center is upward, so $N-mg=mv^2/R$ and $N$ is larger than the weight. For a $2.0\,\mathrm{kg}$ cart at $5.0\,\mathrm{m/s}$ in a loop of radius $1.0\,\mathrm{m}$, $N=2.0(10+25/1.0)=70\,\mathrm{N}$.

At the crest of a rounded hill the center of curvature lies below the car, so weight toward the center and the normal force away from it give $mg-N=mv^2/r$. The fastest speed with the tires still pressing on the road is when $N=0$: $v=\sqrt{gr}$. For $r=25\,\mathrm{m}$, that ceiling is $\sqrt{250}\approx16\,\mathrm{m/s}$. Faster than that, the required $mv^2/r$ exceeds $mg$ and the car leaves the pavement.

On a flat, unbanked curve the static friction force supplies the entire centripetal requirement: $f_s=mv^2/r\le\mu_s N=\mu_s mg$. The smallest friction coefficient that works is therefore $\mu_{s,\mathrm{min}}=v^2/(rg)$. Mass cancels. A car at $15\,\mathrm{m/s}$ on a $45\,\mathrm{m}$ level turn needs $\mu_{s,\mathrm{min}}=(15)^2/(45\cdot10)=0.50$.

A frictionless bank of angle $\theta$ and radius $r$ has design speed set by $\tan\theta=v^2/(rg)$, or $v=\sqrt{rg\tan\theta}$. Only the normal force acts, and its horizontal component equals $mv^2/r$ while its vertical component equals $mg$. For $r=50\,\mathrm{m}$ and $\theta=37^\circ$ with $\tan37^\circ=0.75$, the design speed is $\sqrt{50\cdot10\cdot0.75}=\sqrt{375}\approx19\,\mathrm{m/s}$. When the car goes faster than that design speed, the normal force alone is not enough inward, so friction must point down the bank to add an inward horizontal component.

A conical pendulum is a mass on a string of length $L$ swinging in a horizontal circle with the string at a fixed angle $\theta$ from the vertical. Vertically there is no acceleration, so $T\cos\theta=mg$. The radius of the circle is $r=L\sin\theta$, and horizontally $T\sin\theta=mv^2/r$. Because only the vertical piece of $T$ supports the weight, the tension itself is greater than $mg$. Example: $m=0.40\,\mathrm{kg}$, $L=1.2\,\mathrm{m}$, $\theta=37^\circ$ with $\cos37^\circ=0.80$ and $\sin37^\circ=0.60$ gives $T=(0.40)(10)/0.80=5.0\,\mathrm{N}$, which exceeds the $4.0\,\mathrm{N}$ weight, and $r=(1.2)(0.60)=0.72\,\mathrm{m}$.

Whenever gravity alone (or gravity plus another central force) is what bends a path into a circle, you still write $F_{\mathrm{net, toward\ center}}=mv^2/r$. Orbital details that go beyond that radial force equation belong to topic 2.6.

Key points

  • $a_c=v^2/r$ toward the center; with period $T$, $v=2\pi r/T$ and $a_c=4\pi^2 r/T^2$. Doubling $v$ multiplies $a_c$ by $4$.
  • Net force toward the center is $mv^2/r$. Do not invent an outward force on the free-body diagram.
  • Speeding up adds a tangential $a_t$; total $a=\sqrt{a_c^2+a_t^2}$. Near rest, $a_c$ is small so $a_t$ dominates.
  • Loop top (inside): $N+mg=mv^2/R$; contact limit $v=\sqrt{gR}$ when $N=0$. Loop bottom: $N-mg=mv^2/R$.
  • Hill crest: $mg-N=mv^2/r$; leave-road limit $v=\sqrt{gr}$ when $N=0$.
  • Flat curve: $\mu_{s,\mathrm{min}}=v^2/(rg)$; mass cancels.
  • Frictionless bank: $\tan\theta=v^2/(rg)$ and $v=\sqrt{rg\tan\theta}$. Faster than design speed, friction points down the bank.
  • Conical pendulum: $T\cos\theta=mg$, $r=L\sin\theta$, $T\sin\theta=mv^2/r$, and $T>mg$.

Moving at constant speed in a circle still requires a net force, because the direction of the velocity is changing.

Practice this topic