TOPIC 5.3 · STUDY
Torque
Torque measures how effectively a force tends to rotate an object about an axis. Magnitude is r F sin theta or F times the lever arm. Sign follows a chosen convention, couples give pure rotation, and weight acts at the center of mass. Units are N m, not joules of energy.
5.3.A
Torque
Torque describes the rotational effect of a force about a chosen axis. If $\vec{r}$ runs from the axis to the point where the force is applied, the magnitude is $$\tau=rF\sin\theta,$$ where $\theta$ is the angle between $\vec{r}$ and $\vec{F}$. An equivalent form is $$\tau=Fd,$$ where the lever arm $d$ is the perpendicular distance from the axis to the force's line of action. Both formulas give the same number.
The dashed segment labeled $d$ is the lever arm: the perpendicular from the pivot to the line of action of $\vec{F}$. Torque magnitude is $Fd$.
Torque is largest when $\theta=90^\circ$, because $\sin 90^\circ=1$ and the lever arm equals the full distance from the axis to the application point. Torque is zero when the force's line of action passes through the axis: $\sin\theta=0$ and $d=0$. A push straight through a hinge, or a force along a rod aimed into the pivot, produces no rotation about that axis no matter how large $F$ is.
Only the line of action matters for the lever arm. Sliding the application point along the same straight line of action does not change $d$, so the torque about the axis stays the same. You may picture the force as acting anywhere along that line when you compute $\tau=Fd$.
Assign a sign before adding torques. Take counterclockwise as positive and clockwise as negative. Example: about a fixed pivot, one force has lever arm $0.40\,\mathrm{m}$ and produces a $10\,\mathrm{N}$ clockwise torque magnitude, so $\tau_1=-(10)(0.40)=-4.0\,\mathrm{N\cdot m}$. Another force has lever arm $0.20\,\mathrm{m}$ and produces an $8.0\,\mathrm{N}$ counterclockwise torque magnitude, so $\tau_2=+(8.0)(0.20)=+1.6\,\mathrm{N\cdot m}$. The net torque is $-4.0+1.6=-2.4\,\mathrm{N\cdot m}$, which is clockwise.
A couple is a pair of equal, opposite, parallel forces separated by perpendicular distance $d$. The net force is zero, so the pair does not accelerate the center of mass, but the net torque has magnitude $Fd$. That torque is the same about every point in the plane: choosing a different reference point changes the individual lever arms, yet the signed sum stays $Fd$.
The weight of a uniform body may be drawn as a single $mg$ arrow at the center of mass. If the pivot is at the center of mass, the gravitational lever arm is zero and the weight contributes no torque about that pivot. If the center of mass lies a distance $L/3$ from the pivot, the gravitational lever arm for a vertical weight is $L/3$, not half the object's length. Using $L/2$ by habit is wrong whenever the mass center is not midway from the axis.
Consider a uniform rod of length $L$ pivoted at its lower end and raised to an angle $\beta$ above the horizontal. A vertical force applied at the upper end has a lever arm equal to the horizontal distance from the pivot to that force's vertical line of action, which is $L\cos\beta$. When the rod stands vertical, $\beta=90^\circ$, that horizontal distance shrinks to zero, so a vertical push at the free end produces no torque about the lower pivot.
A single-dot free-body diagram keeps force directions for net-force calculations but erases application points. Torque needs both the direction of each force and where it acts, so that diagram cannot be used to compute torques. Draw each force at its true point of application, or mark the lever arm to the line of action, before writing $\tau$.
The SI unit of torque is the newton-meter, $\mathrm{N\cdot m}$. Energy also has units that reduce to $\mathrm{N\cdot m}$, and that shared product is named the joule. Do not call a torque a joule: torque is not energy. Keep the label $\mathrm{N\cdot m}$ for torque and $J$ for energy.
| Situation | Lever arm or torque | Watch for |
|---|---|---|
| Force through the axis | $d=0$, $\tau=0$ | Large $F$ still gives zero torque |
| Force perpendicular to $\vec{r}$ | $d=r$, $\tau=rF$ | Maximum for that $r$ and $F$ |
| Force along a rod into the pivot | $d=0$ | Line of action hits the axis |
| Uniform weight, pivot at CM | $\tau_g=0$ | Do not invent a gravitational torque |
| CM a distance $L/3$ from pivot | Vertical weight uses $d=L/3$ | Not automatically $L/2$ |
| Couple, separation $d$ | Net $\tau=Fd$, net $F=0$ | Same torque about any point |
Key points
- Torque magnitude is $rF\sin\theta$ or $Fd$, with $d$ the perpendicular distance from the axis to the force line.
- Maximum torque at $\theta=90^\circ$; zero when the line of action passes through the axis.
- Moving the application point along the same line of action does not change the torque.
- State a sign convention (counterclockwise positive here) and add signed torques about one axis.
- A couple has net force zero and net torque $Fd$, independent of the reference point in the plane.
- Weight acts at the center of mass; gravitational torque is zero about a pivot at the CM, and the lever arm is the actual CM distance, not a default $L/2$.
- For an angled rod with a vertical end force, the lever arm is the horizontal offset from the pivot and vanishes when the rod is vertical.
- Torque units are $\mathrm{N\cdot m}$; do not confuse them with joules of energy, and do not use a single-dot FBD to compute torques.
A larger force can still produce a smaller torque if its lever arm is smaller.