TOPIC 2.7 · STUDY
Kinetic and Static Friction
Static friction self-adjusts up to mu_s N; kinetic friction is mu_k N once sliding. Normal force sets both limits and depends on how you push, pull, or tilt. Inclines, walls, stacks, and rolling tires all follow the same model with g = 10 m/s^2.
2.7.A
Kinetic and static friction
Friction is a contact force parallel to the surfaces. Static friction acts when there is no sliding between the surfaces in contact. It adjusts to whatever value equilibrium needs, as long as that value stays at or below the maximum $f_{s,\max}=\mu_s N$. If an applied horizontal push is smaller than $f_{s,\max}$, the object stays at rest and the friction force equals the push, not $\mu_s N$. Kinetic friction acts once the surfaces slide. Its magnitude is $f_k=\mu_k N$, usually smaller than the peak static value for the same pair of materials. The course model has no area term: tipping a block onto a smaller face does not change $f_{s,\max}$ if the materials and the normal force stay the same.
| Situation | Friction rule | What to watch |
|---|---|---|
| At rest, push < $\mu_s N$ | $f_s=$ applied force | Do not plug in $\mu_s N$ yet |
| Impending slip | $f_s=\mu_s N$ | Threshold to start motion |
| Sliding | $f_k=\mu_k N$ | Usually $\mu_k<\mu_s$ |
| Same $N$, smaller contact area | Limits unchanged | No area in the model |
On a level surface with no other vertical forces, $N=mg$. A push angled downward increases $N$ because the vertical component adds to the weight. A pull angled upward decreases $N$ because that vertical component partly supports the weight. Changing $N$ changes both $f_{s,\max}$ and $f_k$.
Example with original numbers: a $5.0\,\mathrm{kg}$ box rests on a level floor with $\mu_s=0.50$ and $\mu_k=0.30$. Take $g=10\,\mathrm{m/s^2}$, so $N=50\,\mathrm{N}$, $f_{s,\max}=25\,\mathrm{N}$, and $f_k=15\,\mathrm{N}$. A horizontal push of $18\,\mathrm{N}$ leaves the box at rest with $f_s=18\,\mathrm{N}$. A horizontal push of $28\,\mathrm{N}$ exceeds the maximum, so the box slides with $a=(28-15)/5.0=2.6\,\mathrm{m/s^2}$.
Friction matches the pull until the peak, then drops to kinetic friction. The rising segment has slope $1$ while the object is stuck; after breakaway, $f$ stays at the smaller kinetic value even if the pull keeps growing.
On an incline of angle $\theta$, the normal force is $N=mg\cos\theta$. The component of weight down the slope is $mg\sin\theta$. The block slips when $mg\sin\theta>\mu_s mg\cos\theta$, or $\tan\theta>\mu_s$. Mass cancels, so the critical angle depends only on the surface pair. While the block is still at rest on a gentler slope, static friction equals $mg\sin\theta$, not automatically $\mu_s N$. While sliding down, $a=g(\sin\theta-\mu_k\cos\theta)$. While sliding up, kinetic friction also points down the slope, so $a=g(\sin\theta+\mu_k\cos\theta)$, a larger magnitude than on the way down.
Example: $\theta=37^\circ$ with $\sin\theta=0.60$ and $\cos\theta=0.80$, and $\mu_k=0.25$. Sliding down gives $a=10(0.60-0.25\cdot 0.80)=4.0\,\mathrm{m/s^2}$. Sliding up gives $a=10(0.60+0.25\cdot 0.80)=8.0\,\mathrm{m/s^2}$.
A block pressed against a vertical wall by a horizontal force $F$ has normal force $N=F$. Static friction must support the weight, so $\mu_s F\ge mg$ and the smallest holding push is $F_{\min}=mg/\mu_s$. Because $\mu_s$ is often less than $1$, that push is typically larger than the weight.
For stacked blocks accelerating together, or a crate riding in a truck bed, only static friction supplies the horizontal acceleration of the upper object. The largest shared acceleration without slipping is $a_{\max}=\mu_s g$. Mass cancels. On a level surface that brings a sliding object to rest, $a=\mu_k g$ opposite the velocity, so the stopping distance is $d=v^2/(2\mu_k g)$; mass cancels again.
Drive tires accelerate a car through static friction. The driven tire tends to push the road backward, so the road pushes the tire forward. Rolling without slipping means the contact patch is not sliding on the pavement, so that forward force is static friction even though the car as a whole is moving. If the tires spin, kinetic friction replaces the larger available static force and the forward acceleration drops.
To measure $\mu_s$, slowly tilt a board until the object first slips and use $\mu_s=\tan\theta$ at that critical angle. To measure $\mu_k$, find the acceleration down a known incline from $a=g(\sin\theta-\mu_k\cos\theta)$, or use a hanging-mass setup on a level track: if hanging mass $m$ pulls block mass $M$ with measured acceleration $a$, then $mg-\mu_k Mg=(M+m)a$.
Key points
- Static friction equals whatever keeps equilibrium, up to $\mu_s N$; kinetic friction is $\mu_k N$ once sliding.
- No area term: same materials and same $N$ give the same friction limits.
- Level surface: $N=mg$ unless an angled force changes it; down-push raises $N$, up-pull lowers $N$.
- Incline: $N=mg\cos\theta$; slip when $\tan\theta>\mu_s$; at rest $f_s=mg\sin\theta$.
- Down the incline $a=g(\sin\theta-\mu_k\cos\theta)$; up, friction adds, so $a=g(\sin\theta+\mu_k\cos\theta)$.
- Wall hold: smallest $F$ is $mg/\mu_s$. Stacks and truck beds: $a_{\max}=\mu_s g$.
- Stopping distance $v^2/(2\mu_k g)$ and $a_{\max}=\mu_s g$ are mass-independent.
- Drive tires: forward static friction from the road accelerates the car.
- Measure $\mu_s$ from the tilt angle; measure $\mu_k$ from incline or hanging-mass acceleration.
Static friction equals the applied force while the object is at rest; $\mu_s N$ is only the maximum.