TOPIC 5.1 · STUDY

Rotational Kinematics

Rotational kinematics for a rigid body: signed angular displacement in radians, average omega and alpha, constant-alpha equations, and reading slopes and signed areas on theta, omega, and alpha versus time graphs.

5.1.A

Rotational kinematics

Rotational kinematics tracks how a rigid object turns. Pick a positive sense once (this course takes counterclockwise as positive when a sign is needed) and measure angles in radians. Angular displacement $\Delta\theta$ is the unwrapped signed angle the body sweeps, not the final facing of a painted mark. Three full turns counterclockwise give $\Delta\theta=+6\pi$ rad even though the wheel looks identical afterward. Crossing from $350^\circ$ to $10^\circ$ while still turning counterclockwise is $+20^\circ$, not $-340^\circ$; the short wrap-around difference on a dial is not the displacement.

On a rigid wheel every off-axis point sweeps that same $\Delta\theta$ in the same time. A camera that sees a marker in the same place in consecutive frames cannot tell whether the wheel sat still or completed an integer number of turns between frames; the image alone does not reveal the unwrapped angle.

Average angular velocity is $\omega_{\mathrm{avg}}=\Delta\theta/\Delta t$. Average angular speed uses the total angle traveled and does not cancel opposite directions. Example: a shaft turns at $+4\,\mathrm{rad/s}$ for $2\,\mathrm{s}$, then at $-2\,\mathrm{rad/s}$ for $3\,\mathrm{s}$. Net displacement is $(+4)(2)+(-2)(3)=+2$ rad, so $\omega_{\mathrm{avg}}=2/5=0.40\,\mathrm{rad/s}$. Angle traveled is $|4|(2)+|-2|(3)=14$ rad, so the average angular speed is $14/5=2.8\,\mathrm{rad/s}$.

Average angular acceleration is $\alpha_{\mathrm{avg}}=\Delta\omega/\Delta t$. Constant $\omega$ means $\alpha=0$, not that the wheel is stopped: a flywheel spinning steadily at $15\,\mathrm{rad/s}$ has zero angular acceleration. If $\omega$ changes from $+5.0\,\mathrm{rad/s}$ to $-1.0\,\mathrm{rad/s}$ in $2.0\,\mathrm{s}$, then $\alpha_{\mathrm{avg}}=(-1.0-5.0)/2.0=-3.0\,\mathrm{rad/s^2}$.

When $\alpha$ is constant the linear-motion analogs hold with angle in place of position: $\omega=\omega_0+\alpha t$, $\theta=\omega_0 t+\tfrac12\alpha t^2$, and $\omega^2=\omega_0^2+2\alpha\theta$ (taking $\theta=0$ at the start). From rest, $\theta=\tfrac12\alpha t^2$, so $\theta$ is proportional to $t^2$. To reach a fixed final speed from rest, $\theta=\omega^2/(2\alpha)$ is inversely proportional to $\alpha$: larger angular acceleration means less angle is needed to hit the same $\omega$.

Example with constant $\alpha$: a disk starts at rest with $\alpha=+2.5\,\mathrm{rad/s^2}$ for $4.0\,\mathrm{s}$. Then $\omega=(2.5)(4.0)=10\,\mathrm{rad/s}$ and $\theta=\tfrac12(2.5)(4.0)^2=20$ rad. Doubling $\alpha$ to $5.0\,\mathrm{rad/s^2}$ while keeping the same final $\omega=10\,\mathrm{rad/s}$ cuts the needed angle in half to $\theta=10^2/(2\cdot 5.0)=10$ rad.

Graph Slope Signed area
$\theta$ versus $t$ $\omega$ (not used for $\omega$ or $\alpha$)
$\omega$ versus $t$ $\alpha$ $\Delta\theta$
$\alpha$ versus $t$ (jerk; rarely needed) $\Delta\omega$

The figure below is a straight $\omega(t)$ line from $(0,6)$ to $(6,-6)$. The constant slope is $\alpha=(-6-6)/6=-2\,\mathrm{rad/s^2}$. The line crosses zero at $t=3\,\mathrm{s}$.

Angular velocity versus time: a straight line from 6 rad/s at t=0 to -6 rad/s at t=6 s.

Signed area under $\omega(t)$ from $0$ to $6\,\mathrm{s}$ is a $+9$ rad triangle then a $-9$ rad triangle, so $\Delta\theta=0$. Slope stays $-2\,\mathrm{rad/s^2}$ the whole time.

If $\alpha$ opposes $\omega$, angular speed falls and the rotation can reverse. Worked case: $\omega_0=+8\,\mathrm{rad/s}$ and $\alpha=-2\,\mathrm{rad/s^2}$. The wheel stops when $\omega=0$: $0=8-2t$ gives $t=4\,\mathrm{s}$. At $t=8\,\mathrm{s}$, $\omega=8+(-2)(8)=-8\,\mathrm{rad/s}$. From $0$ to $4\,\mathrm{s}$ the angle is $\theta=8(4)+\tfrac12(-2)(4)^2=16$ rad; from $4$ to $8\,\mathrm{s}$ it sweeps another $16$ rad the other way, so net $\Delta\theta=0$ while the total angle traveled is $32$ rad.

Key points

  • Angular displacement is the unwrapped signed angle in radians; looking the same again does not mean $\Delta\theta=0$.
  • Counterclockwise is the usual positive sense once you choose a sign convention.
  • Average $\omega$ is $\Delta\theta/\Delta t$; average angular speed uses angle traveled and does not cancel reverse turns.
  • Average $\alpha$ is $\Delta\omega/\Delta t$; steady nonzero $\omega$ still means $\alpha=0$.
  • Constant $\alpha$: $\omega=\omega_0+\alpha t$, $\theta=\omega_0 t+\tfrac12\alpha t^2$, $\omega^2=\omega_0^2+2\alpha\theta$.
  • From rest, $\theta\propto t^2$; for fixed final $\omega$, $\theta\propto 1/\alpha$.
  • Slope of $\omega(t)$ is $\alpha$; signed area under $\omega(t)$ is $\Delta\theta$; signed area under $\alpha(t)$ is $\Delta\omega$.
  • Every off-axis point on a rigid wheel shares the same angular displacement; a still marker on film cannot rule out whole-turn jumps.

Returning to the same orientation is not the same as zero angular displacement.

Practice this topic